Game Console Button and Joystick Repair Houston TX that ends drift fast
Same-day button and joystick repair for PlayStation, Xbox, and Switch
Game Console Button and Joystick Repair Houston TX is what we do every day at our Harris County bench. If your controller drifts left, a face button sticks, or a thumbstick clicks without input, bring it in and we will diagnose it free. We replace the joystick module, clean the contact pads, and test every input before you pay. Most button and joystick repair Houston TX jobs are finished the same day you drop off.
Game Console Button and Joystick Repair Houston TX explained
Game console button and joystick repair Houston TX is the electronic service that restores failed inputs on controllers and handhelds, replacing worn joystick modules, dome switches, and membrane contacts so every press and push registers correctly again. We open the shell with precision screwdriver set bits, inspect the board under magnification, and check each button trace with a multimeter. On a DualSense or Switch Joy-Con, the usual culprit is a worn potentiometer inside the joystick module, not the board itself. We desolder the old module at a soldering station, fit a fresh one, and calibrate it before reassembly.
Houston gamers put serious hours on their gear, and our humidity plus summer heat makes it worse. Sweat and dust work into the stick housing, and drift shows up months earlier than it should. If you searched joystick fix near me Houston open now, we keep same-day slots open for drop-offs at our bench. We also see plenty of Xbox joystick repair Houston Texas requests from players in Katy and Cypress whose controllers sat in hot cars. A $12 module and an hour of bench time beats a $70 replacement pad.
Why Houston players choose our bench
We fix inputs, not symptoms. Every job gets a full input test, a calibration pass, and a 90-day warranty on the parts we install.
Same-day turnaround
Most button and joystick repair Houston TX jobs are done in 60 to 120 minutes while you wait. We keep DualSense, Xbox, and Switch modules in stock, so you are not waiting on a shipment. Drop off before 4 PM and you will usually pick it up the same evening.
Free input diagnosis
We test every button, trigger, and stick axis on a diagnostic rig before quoting. If the drift is software-side, we tell you and charge nothing. If it is a worn module, you get a flat price before we touch the shell. No surprises, no upsell on parts you do not need.
Real parts, not knockoffs
We fit OEM-spec joystick modules and membrane pads, not the $3 bulk packs that fail in six weeks. Our soldering station runs at controlled temperature so the pads and traces stay intact. That is why our drift repairs hold up through months of ranked play instead of days.
90-day parts warranty
Every joystick module and button membrane we install carries a 90-day warranty. If drift returns inside that window, bring it back and we redo the work at no charge. We have been at this since 2020, and repeat customers from the Heights and Bellaire are most of our bench traffic.
How our repair process works
Five steps, one bench, no runaround. You drop off, we diagnose, quote, repair, and test before you pay.
Drop-off and intake
Bring your controller or handheld to our Houston bench, or call +1 832-581-0001 to reserve a same-day slot. We log the model, serial, and the exact symptoms you describe. Intake takes five minutes, and you get a claim ticket by text.
Free input diagnosis
We connect the pad to a diagnostic rig and map every axis and button. Drift is measured in raw values, not guesses. You get a call or text with the finding and a flat quote within 30 minutes of drop-off on most days.
Teardown and inspection
Once you approve, we open the shell with ESD-safe tweezers and a precision screwdriver set. The board gets a look under magnification for corrosion, cracked solder, or liquid damage. We photograph anything unusual so you can see what we see.
Module replacement
We desolder the worn joystick module at a temperature-controlled soldering station, clean the pads with flux, and fit the replacement. Button membranes and dome switches get swapped at the same time when they are worn. This step runs 45 to 90 minutes depending on the model.
Calibration and test
After reassembly we recalibrate the sticks in the console's own menu, then run a 10-minute input test across every button and axis. You get a printed test sheet with the before and after values. Pay only when the pad passes.
Bench experience you can verify
We have run a dedicated game console repair bench in Houston since 2020, and input repair is most of what crosses it. Our technicians hold IPC-A-610 certified soldering credentials and work ESD-safe on every board. We have repaired thousands of DualSense, Xbox, and Switch controllers, plus a steady stream of Sega and Atari pads from collectors. We stock OEM-spec joystick modules, membrane pads, and dome switches so most jobs never wait on parts. If a repair is not worth doing, we say so and hand the pad back.
- IPC-A-610 certified soldering on every board-level joystick replacement
- ESD certification and grounded mats at all five bench stations
- OEM-spec joystick modules stocked for PlayStation, Xbox, and Switch
- CompTIA A+ trained technicians who document every repair with photos
- Thousands of controller inputs repaired since opening in 2020
Why our game console button and joystick repair Houston TX stands out
We are a repair bench, not a reseller. You get a flat quote, a real diagnosis, and a warranty on the parts we install.
Flat pricing, no surprises
You approve the price before we open the shell. A standard joystick module swap runs $45 to $75 in 2026, and button membrane work runs $35 to $60. No diagnostic fee, no bench fee, no charge if we cannot fix it. That is the whole pricing model.
Parts always in stock
We keep OEM-spec modules for DualSense, DualShock 4, Xbox Series, Xbox One, and Switch Joy-Con on the shelf. That means console joystick fix Houston jobs finish the same day instead of waiting a week on shipping. If a part is unusual, we tell you the lead time upfront.
Board-level skill
Drift is not always the module. Sometimes it is a cracked trace or a lifted pad from a previous DIY repair. Our technicians read schematics and repair traces under magnification, so a botched home fix does not mean a dead controller. We see this weekly from button repair near me Houston walk-ins.
Tested before you pay
Every pad leaves the bench with a printed input test showing stick values and button response. If you searched game console button and joystick repair Houston TX same day, this is how we back that promise. You see the numbers, you test it yourself, then you pay.
What our button and joystick repair covers
Our standard service covers the inputs that fail most: analog sticks, face buttons, D-pad, bumpers, and triggers. Board-level work, shell replacement, and cosmetic parts are quoted separately once we see the unit. Everything below is included in the flat bench price.
What's Included
Analog stick replacement
We desolder the worn joystick module and fit an OEM-spec replacement, then recalibrate both axes in the console menu. This fixes drift, dead zones, and sticks that snap back to center slowly. Typical bench time is 45 to 90 minutes per stick.
Button membrane service
Sticky or unresponsive face buttons usually mean a worn rubber membrane or dirty contact pad. We clean the pads with isopropyl, replace the membrane when needed, and test every button press on the diagnostic rig. Most membrane jobs finish in under an hour.
Trigger and bumper repair
L1, R1, L2, and R2 fail from spring fatigue and cracked plastic pivots. We replace the spring, pivot, or the whole trigger assembly depending on what failed. You get full analog travel back on both triggers, verified on the test rig.
D-pad and face button contacts
We clean and re-tension the dome switches under the D-pad and face buttons. If a contact is torn, we repair the trace or replace the contact pad. Every direction and button gets a press test before the shell goes back on.
Full input calibration
After any repair we run a 10-minute input sweep across every button, stick, and trigger, then recalibrate in the console menu. You get a printed test sheet with before and after values so you can see the fix, not just take our word for it.
Input problems we fix every week in Houston
These are the four failures that fill our bench. Each one has a known cause and a known fix, and none of them require buying a new controller.
Stick drift that pulls your aim off target
Drift ruins ranked play, makes menus unusable, and gets worse every week until the stick is dead. Most players replace a $70 pad when a $12 module is the real fix.
We measure the drift in raw values, replace the worn joystick module at the soldering station, and recalibrate both axes. You get the before and after numbers on a printed test sheet. Most drift repairs finish the same day.
Face buttons that stick or stop registering
A stuck button fires inputs you did not press, and a dead button locks you out of menus. Both get worse with sweat and dust working into the membrane.
We open the shell, clean the contact pads with isopropyl, and replace the rubber membrane if it is torn or flattened. Every button gets a press test on the rig. Typical cost runs $35 to $60 with parts.
Triggers with no analog travel
Racing and shooter games need full trigger range. A snapped spring or cracked pivot turns a precise trigger into an on-off switch, and it usually fails mid-match.
We replace the spring or the full trigger assembly, depending on what broke. You get smooth analog travel back on both triggers, verified on the diagnostic rig before reassembly. Most jobs finish in under an hour.
Joy-Con drift on Switch handhelds
Switch Joy-Con drift makes handheld play unusable and shows up fast in Houston humidity. Nintendo Switch joystick repair Houston TX requests are one of our most common walk-ins.
We fit a fresh joystick module in the Joy-Con rail, recalibrate in the Switch menu, and test both sticks across the full range. Same-day turnaround on most Joy-Con pairs, with a 90-day parts warranty.
When to bring your controller in
A ranked player in Midtown whose DualSense drifts left during every match
We measure the drift, replace the joystick module, and recalibrate both sticks in the console menu. The whole job runs about 90 minutes at the bench, and you get the before and after values on paper.
Aim stays centered through long sessions, and the pad plays like it did out of the box.
A parent in Bellaire with two Switch Joy-Con that drift and a sticky B button
We replace both joystick modules, clean the button contacts, and replace the worn membrane. Both Joy-Con get a full input test and a calibration pass in the Switch menu before pickup.
Both kids are back on handheld play the same evening, and the pair carries a 90-day parts warranty.
A collector in the Heights with an original Xbox controller and a mushy D-pad
We clean and re-tension the dome switches under the D-pad, then test every direction on the rig. Older pads sometimes need a contact pad replacement, which we quote before starting.
The D-pad clicks cleanly again, and the pad stays original instead of being replaced with a modern knockoff.
A Cypress gamer whose controller sat in a hot car and now has a dead right stick
We inspect the board for heat damage, replace the joystick module, and check the surrounding traces under magnification. If the board itself is damaged, we quote board-level repair before proceeding.
The right stick works across its full range again, and you avoid buying a replacement pad.
Tools and methods on our bench
Tools & Equipment
Hakko soldering station
Temperature-controlled desoldering and reflow of joystick modules without lifting pads or damaging nearby traces. We run it at calibrated temperatures for each board type.
Hot air rework station
Used for multi-pin module removal and board-level work where a soldering iron alone would spread too much heat. It lets us remove a module cleanly in one pass.
Multimeter
Continuity and voltage checks on button traces, stick potentiometers, and trigger contacts. This is how we confirm a fault before quoting a repair.
ESD-safe tweezers and mats
Grounded work surfaces and non-static tools protect the board from static discharge during teardown. Every bench station is ESD certified.
Precision screwdriver set
Correct-fit bits for Tri-wing, Torx, and Phillips screws on PlayStation, Xbox, and Switch shells. The right bit prevents stripped screws and cracked posts.
Ultrasonic cleaner
Deep-cleans sticky button membranes, contact pads, and shells after sweat and soda exposure. It removes residue that isopropyl alone will not lift.
Compressed air
Clears dust and debris from stick housings, fan intakes, and button wells before reassembly. Dust is a leading cause of premature stick wear in Houston.
Methods & Techniques
IPC-A-610 certified soldering
Every board-level repair follows IPC-A-610 workmanship standards for solder joints and pad integrity. That means clean, shiny joints with the right fillet, not blobs that fail in a month. It is the same standard used in commercial electronics manufacturing.
ESD-safe teardown
We work on grounded mats with wrist straps and ESD-safe tools from the first screw to the last. Static discharge is invisible and can kill a controller board without leaving a mark. Our ESD certification is why we do not skip this step.
Raw-value drift measurement
Before and after every stick repair, we read the raw axis values on a diagnostic rig. Drift is a number, not a feeling. You get those numbers on a printed test sheet so the fix is verifiable, not a claim.
Console-menu recalibration
After a module swap we recalibrate the sticks in the console's own settings menu, not just on the bench rig. This matches the pad to your console and catches any axis that is still slightly off before you take it home.
How button and joystick repair runs in Houston
Houston's humidity and summer heat are hard on controller inputs. Sweat works into stick housings, dust from ceiling fans and open windows settles into button wells, and pads left in hot cars see drift months earlier than the same pad in a drier climate. We see this pattern across Harris County, from Downtown Houston high-rises to garages in Katy and Cypress. Our bench keeps OEM-spec modules in stock so a console joystick fix Houston job usually finishes the same day you drop off. If you searched button and joystick repair Downtown Houston, we are a short drive from the EaDo and Third Ward corridors and take walk-ins during bench hours. We also handle mail-in repairs from Clear Lake, Webster, and Friendswood when driving in is not practical. Texas sales tax permit on file, and every repair is documented with photos and a printed input test.
Service Areas
Walk-in traffic from office workers and loft residents who drop a drifting DualSense off at lunch and pick it up after work. Same-day slots fill fast on weekdays.
A steady stream of Switch Joy-Con and retro Sega pads from collectors. Older pads often need contact cleaning before any module work.
Family households with multiple consoles and kids' controllers. We see a lot of sticky buttons from snack residue and sweaty hands.
Mail-in repairs are common here because of the drive. We send a prepaid label and return the pad tested and calibrated.
Local Considerations
High humidity most of the year
Moisture and sweat accelerate corrosion on stick potentiometers and button contacts. We clean and treat contacts on every job to slow that down.
Summer heat inside parked cars
Controllers left in hot vehicles can warp plastic pivots and stress solder joints. We inspect the board for heat damage before quoting a repair.
Dust from fans and open windows
Dust packs into stick housings and button wells, causing premature wear. We blow out every unit with compressed air before reassembly.
DualSense drift fixed in 90 minutes
A Midtown player brought in a DualSense that drifted hard left in every shooter. Raw axis values showed the left stick resting 22 percent off center, well past the dead zone. The pad was eight months old and otherwise in good shape.
We replaced the left joystick module, recalibrated both sticks in the console menu, and ran a full input sweep. Post-repair values sat within 2 percent of center. Total bench time was 90 minutes, and the pad passed every button test.
Maintenance & Follow-up
Keep the pad out of hot cars and wipe the stick wells monthly with a dry microfiber cloth. Avoid compressed air directly into the stick housing, which can push dust deeper.
A Bellaire parent dropped off two Joy-Con with drift on both sticks and a B button that stuck. The kids had been using them daily for over a year, and the membranes were flattened from heavy play.
We replaced both joystick modules, cleaned the button contacts, and fitted new membranes. Both Joy-Con recalibrated cleanly in the Switch menu and passed the full input test. The pair was ready for pickup the same evening.
Maintenance & Follow-up
Wipe the Joy-Con rails and button wells weekly, and store the Switch in a case rather than a bag. That keeps dust and crumbs out of the button wells.
A Cypress gamer's Xbox controller had an R2 trigger with no analog range, just on or off. The spring had snapped and the plastic pivot was cracked. The rest of the pad, including both sticks, tested fine.
We replaced the trigger spring and pivot assembly, then verified full analog travel on the diagnostic rig. R2 read smoothly from 0 to 100 percent across ten test presses. The job took under an hour and cost less than a new pad.
Maintenance & Follow-up
Avoid pressing triggers hard against the stop during play, and keep the pad dry. Sweat and soda are the two fastest ways to kill a trigger pivot.
What button and joystick repair costs
Typical 2026 pricing in Houston runs $35 to $75 for a single input repair, with most jobs landing around $55. A joystick module swap is $45 to $75 depending on the model, and button membrane work is $35 to $60. Multi-stick jobs and board-level repairs are quoted after diagnosis. There is no diagnostic fee, and you approve the price before we open the shell. If you searched console joystick fix Houston and want a number before you drive in, call us with the model and symptoms.
Pricing Factors
Number of sticks
A single drifting stick is the base price. Replacing both sticks on the same pad adds bench time and a second module, so the total rises. We quote the pair price upfront when both are worn.
Console model
DualSense and Xbox Series modules are straightforward. Switch Joy-Con and older DualShock 4 pads have tighter tolerances and more fragile ribbon cables, which adds 15 to 30 minutes of bench time.
Board condition
If a previous DIY repair lifted pads or cracked a trace, we repair the board before fitting the new module. That board-level work is quoted separately once we see the damage under magnification.
Parts quality
We fit OEM-spec modules and membranes, which cost more than the bulk knockoff packs. The price difference is why our drift repairs hold up for months instead of weeks, and why we warranty the parts for 90 days.
Rush service
Standard turnaround is same day for most jobs. If you need a repair finished within a specific window, tell us at drop-off and we will confirm whether we can hit it before you leave the unit.
Typical Investment Range
$35 - $120 depending on scope
Actual pricing varies based on project scope and requirements
Value You Receive
A new DualSense or Xbox pad runs $60 to $75, and a Switch Joy-Con pair runs $80 or more. A $55 module swap keeps the controller you already know, avoids the break-in period on a new stick, and comes with a 90-day parts warranty.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsHow much does button and joystick repair cost in Houston?
Most jobs run $35 to $75 in 2026, with a single joystick module swap at $45 to $75 and button membrane work at $35 to $60. Multi-stick jobs and board-level repairs are quoted after diagnosis. There is no diagnostic fee, and you approve the price before we open the shell. If we cannot fix it, you pay nothing.
Where to fix console joystick in Houston TX?
Bring it to our Houston bench, or call +1 832-581-0001 to reserve a same-day slot. We serve walk-ins from Downtown, Midtown, the Heights, and Bellaire, and we take mail-in repairs from Clear Lake, Webster, and Friendswood. Most console joystick fix Houston jobs finish the same day you drop off.
Can I fix PS5 joystick in Houston?
Yes. PS5 joystick repair Houston is one of our most common jobs. We replace the worn module at the soldering station, recalibrate both sticks in the console menu, and run a full input test. Most DualSense repairs finish in 90 minutes, and the new module carries a 90-day parts warranty.
Who repairs console buttons near me Houston?
We do. Our technicians hold IPC-A-610 certified soldering credentials and work ESD-safe on every board. We repair sticky face buttons, dead D-pad directions, and mushy triggers on PlayStation, Xbox, Switch, and retro pads. Every button gets a press test on the diagnostic rig before you pay.
Credentials and customer proof
Certifications
Customer Reviews
Brought in a DualSense with bad drift and they fixed it in under two hours. They showed me the raw stick values before and after, which I did not expect. The pad has been solid for months now. Way better than buying a new controller.
Two Switch Joy-Con with drift and a sticky button. They replaced both modules and cleaned the contacts the same day. My kids were back on the Switch that evening. Fair price and they did not try to upsell me on anything.
My Xbox R2 trigger had no range left. They replaced the spring and pivot in under an hour and tested it in front of me. Honest pricing and they explained exactly what failed. I will bring my other controllers here.
Dropped off an old Sega pad with a mushy D-pad. They cleaned the contacts and re-tensioned the switches instead of pushing a replacement. It clicks like new again. Good communication throughout and no surprise charges.
Related Services
Explore our other professional services
PlayStation Repair
Full PlayStation service covering HDMI port damage, disc drive faults, and power issues. If your DualSense drift is fixed but the console itself will not read discs, this is the next step. We handle PS4 and PS5 board-level work at the same bench.
PlayStation RepairXbox Repair
Xbox console repair for disc drive failures, overheating shutdowns, and HDMI port damage. Many Xbox controller drift jobs come in alongside a console that needs a fan and cooling service. We test both together so you leave with a working setup.
Xbox RepairNintendo Switch Repair
Switch repair for Joy-Con drift, charging port issues, and screen replacement. Joy-Con stick work pairs naturally with our button and joystick service, and we calibrate both sticks in the Switch menu before pickup.
Nintendo Switch RepairRetro Console Repair
Repair for Sega, Atari, and other classic consoles, including controller port and button contact work. Retro pads often need contact cleaning before any module replacement, which we handle at the same bench.
Retro Console RepairGame Console HDMI Port Repair
HDMI port replacement using a reballing kit and hot air rework station. If your controller works but the console shows no signal, this is usually the fix. We quote it after inspecting the port and surrounding traces.
Game Console HDMI Port RepairGame Console Power Jack Repair
Power jack replacement for consoles that will not charge or only charge at an angle. A failing jack can also cause intermittent shutdowns that look like controller problems. We test the jack and the board together.
Game Console Power Jack RepairGame Console Controller Repair
Broader controller service covering triggers, bumpers, shells, and charging ports. If your issue is more than sticks and buttons, this service covers the rest. We diagnose the whole pad before quoting.
Game Console Controller RepairGame Console Disc Drive Repair
Disc drive repair for consoles that will not read discs or make grinding noises. A worn laser lens is often the cause. We replace the lens or the drive assembly depending on the model.
Game Console Disc Drive RepairGame Console Hard Drive Replacement
Hard drive and SSD replacement for consoles with slow load times or drive errors. We transfer your data where possible and confirm the new drive reads cleanly before pickup.
Game Console Hard Drive ReplacementGame Console Fan and Cooling Repair
Fan replacement and cooling service for noisy or overheating consoles. Dust-clogged fans are common in Houston, and they shorten console life. We clean the intake and replace the fan when bearings are worn.
Game Console Fan and Cooling RepairGame Console Overheating Repair
Overheating diagnosis and repair, including thermal paste replacement and fan service. Shutdowns mid-game often trace back to dried paste and blocked vents. We measure temperatures before and after.
Game Console Overheating RepairGame Console Software and Firmware Repair
Firmware and software repair for consoles stuck on boot loops or update errors. Sometimes what looks like a hardware fault is a corrupted system file. We diagnose before quoting hardware work.
Game Console Software and Firmware RepairGame Console Data Recovery and Transfer
Data recovery and transfer for saves, profiles, and game libraries. If your console is failing, we pull what we can before repair. We confirm what is recoverable before starting.
Game Console Data Recovery and TransferGame Console Cleaning and Maintenance
Deep cleaning for consoles and controllers, including ultrasonic cleaning of button membranes and contact pads. Regular cleaning is the cheapest way to prevent stick drift and sticky buttons.
Game Console Cleaning and MaintenanceGame Console Custom Modding and Upgrades
Custom mods including shell swaps, LED kits, and upgraded sticks. If you want Hall-effect sticks installed instead of standard modules, this is the service. We quote parts and bench time together.
Game Console Custom Modding and UpgradesGame Console Trade-In and Buyback
Trade-in and buyback for consoles and controllers you no longer use. If a repair is not worth the cost, we will tell you and offer a trade value instead. That keeps you from sinking money into a dead unit.
Game Console Trade-In and BuybackGame Console Accessory Repair
Repair for headsets, charging docks, and other accessories. A failing charging dock can look like a controller battery problem. We test the accessory and the controller together.
Game Console Accessory RepairGame Console Water Damage Repair
Water damage repair with ultrasonic board cleaning and corrosion treatment. Houston spills and storms cause more of these than you would think. Fast drop-off matters, so bring it in as soon as possible.
Game Console Water Damage RepairGame Console Motherboard Repair
Board-level repair for consoles with no power or no video. We trace faults under magnification and repair or replace damaged components. This is the deepest repair we offer.
Game Console Motherboard RepairGame Console Charging Port Repair
Charging port replacement for controllers and handhelds that will not charge reliably. A worn port can also cause intermittent disconnects. We replace the port and test charging under load.
Game Console Charging Port RepairGame Console Screen Replacement
Screen replacement for handhelds with cracked or dead displays. We fit a replacement screen and test touch and display output before pickup. Switch and handheld models are our most common jobs.
Game Console Screen ReplacementGame Console Laser Lens Replacement
Laser lens replacement for disc drives that skip or fail to read. A worn lens is the usual cause of read errors. We test read performance before and after the swap.
Game Console Laser Lens ReplacementGame Console Network and Connectivity Repair
Network repair for consoles that will not connect to Wi-Fi or drop online sessions. Antenna and board faults are the usual causes. We test the connection before and after repair.
Game Console Network and Connectivity RepairGame Console Pre-Purchase Inspection
Pre-purchase inspection for used consoles and controllers before you buy. We check sticks, buttons, disc drives, and ports, then give you a written summary. It is cheap insurance against a bad used purchase.
Game Console Pre-Purchase InspectionWhat Houston players say
Real experiences from customers who chose our Game Console Button and Joystick Repair services
"My DualSense drifted so bad I could not aim. They measured it, replaced the left stick module, and showed me the before and after numbers on a test sheet. Ninety minutes total. It has been three months and the stick is still dead center. I have sent two friends here since."
Marcus T.
Ranked player, Midtown
"Both of my kids' Joy-Con were drifting and the B button stuck on one. They fixed both the same day and cleaned the button contacts. The price was fair and they did not try to sell me new Joy-Con. The kids were back playing that night, which mattered more than anything."
Priya R.
Parent, Bellaire
"I brought in an original Xbox controller with a mushy D-pad and expected to be told it was too old to fix. They cleaned the contacts, re-tensioned the switches, and tested every direction in front of me. It clicks like new. That kind of care is rare."
Danny K.
Collector, The Heights
Book your game console button and joystick repair Houston TX today
We keep same-day slots open for drifting sticks and dead buttons, and every repair carries a 90-day parts warranty. Call +1 832-581-0001 with your model and symptoms, and we will confirm the price before you drive in. Walk-ins welcome at our Harris County bench.